You are currently browsing the category archive for the ‘Pinhole’ category.
Chris Peregoy’s excellent Pinhole Blender has been a device I have employed on numerous occasions to create interesting images. The even inventive one has started marketing what he refers to as a tube camera, which is simply a tube with a pinhole. But one should not be misled with its simplicity, as one can pack a lot within the film employed. The severity in which the film is curved within the tube can offer distortions that distinguish it from a standard flat film plane pinhole image. Of course, a big advantage of the curvature is that each point of the plane has a fairly consistent distance from the pinhole, allowing for even exposure values.
I have only started using this contraption, the 8×10″ version, and displayed is my first successful attempt. It took a few tries because I believe that the exposure time Chris offers is short for my tastes, as this required about three minutes of 100 speed film. I look forward to playing around with this in the future to take advantage of the possibilities.
One some days the sun appears to be more overbearing than others, and this can be magnified by going to the beach. It had been a while since the last time I sat on a beach. That time I got sunburned – not on the face, arms, back or legs, as they all had plenty of sun block – but on the tops of my feet. The result was large blisters (the one on my left foot covered nearly the entire top of the foot) and an inability to stand (I could walk, but only stand in a single place for a few seconds).
On this particular day I returned to the beach, but consciously employed sun block to the tops of my feet. I decided to print this particular pinhole negative as a lith print to accentuate the blast of the sun. An added benefit of the pinhole image is the mysterious white flare shooting onto the umbrella in laser-like fashion. This print was made on one of the few sheets of Ektalure in my possession. I had initially thought of toning the print, but think that the color works just fine for my purposes.
Danger – long post ahead!
I have been looking at my website during these cold days and reconsidering its contents. In doing so, I came across an article I wrote over 15 years ago (pre-digital), and realized how it applies even more today. A few months back I came across someone who remembered reading the article and was all over the place about being glad to meet me because it had had an impact on him and his work. One cannot buy the feeling that accompanies this experience.
So I’ve decided to offer the article in two parts. Sometimes it’s a good idea to go all the way back to the beginning.
As the proliferation of technology continues to force its way into our lives, the hobby of producing images through photographic means has followed suit. Every aspect, from the exposure of film, through print production, has offered the photographer the ability to lose control of the art form. Whereas this may increase production, one wonders who should actually be allowed to sign the final product.
As a means of reversing this tendency in my own work, I decided to take complete control of as many aspects as I felt technically feasible. This sent me in two directions: expose the negative, not with an expensive automatic-everything camera, but with a pinhole camera, and create the print, not with commercially-produced paper, but coat my own and print using the sun. Stone knives and bear skins.
This article is the first of two parts where I will suggest that looking backward, when everyone else is looking forward, may be a consideration not only for contrarians, but also for those who wish to separate themselves from the field. Do I suggest tossing our cameras and paper away to follow this path? I would no more do so than suggest one remain using a single film, paper, and set of chemicals. This is a direction, a means of extending oneself, a way of improving other aspects of one’s photography by seeking another posture.
Part I – Stone Knives
Pinhole takes us to the very essence of photography. At this level, depth of field no longer has meaning, captured light strikes the film plane without the intervention of any modifying factors, and the creation of the tool can be done entirely with materials one already owns. Doing this, we are separated from the mainstream and have the capability to create unique images. Is this not what artists aspire to obtain?
Pinhole photography returns us, perhaps, to the very beginning of photography (it is possible that the first photograph by Niépce in 1826, an eight hour exposure, was a pinhole image). Of course, this idea has been around considerably longer. Ibn al-Haitham (965-1039 AD) wrote of the use of the pinhole to study light rays, Theodoric of Freiberg and Kamal al-Din al-Farisi (14th century) independently used the pinhole to explain the rainbow’s color principals, and some Italian cathedrals in the 15th century contained a pinhole in the ceiling to tell the time. The first use of the camera obscura (a term coined by the astronomer Johannes Kepler) was used by Gemma Frisius to study the solar eclipse of 1544.
The basics of pinhole photography is very simple. Light enters a light-tight box through a very small, lensless aperture, striking the film. If this was the only principle involved, could increase the sharpness of the resultant image by reducing the size of the aperture. However, another element, diffraction, comes into play. This was first demonstrated by the Italian physicist, Francesco Grimaldi, in 1665, where light passing through two consecutive pinholes displayed wider than it should have. The smaller hole, therefore, will increase diffraction, working against the image’s sharpness. The photographer working to obtain the sharpest possible image needs to find a balance between these two conditions.
In addition to this diffraction, it was noted that the boundaries showed coloration. The wave theory indicates that the wavelength is a determining factor of the resulting diffraction — the longer the wavelength, the greater the diffraction. As the red end of the visible spectrum has a greater wavelength than the purple, it is diffracted more, and will show on the outer boundaries.
The nuts and bolts of pinhole photography can be as extravagant, or plain, as complex or simple, as imaginative or straightforward as one may wish. A good starting point is to determine how to make the hole and how large it should be. The instructions I will give have yielded for me quality round pinholes that yield a surprising sharpness. Certainly, if one wishes to work for a less sharp image, simply deviate from the suggested size or roundness of the hole.
There is no consensus as to exactly which proposed formula will actually yield the aperture value for optimum pinhole size. I have relied on the following formula primarily because of its simplicity.
A = square root of 55 * F, where A is the aperture in thousandths of an inch and F is the focal length in inches.
For instance, if your focal length is 10″, the square root of 10 * 55 is 23.45 thousandths of an inch. It is best to convert this to millimeters, as I will explain, so our final value is 0.02345 * 25.4, or .59mm.
The material for creating the pinhole can be anything thin and easy to work with, and I have found aluminum pie pans to work nicely. Cut 1″ X 1.5″ strip and tape it onto a surface. Break a sewing needle in half and shove the blunt end into a pencil eraser. Place the sharp end of the pin in the middle of the aluminum and gently rotate the pencil, barely exerting pressure. Soon, you can remove the needle and find that a hole has been formed. Remove the tape, turn the aluminum over, and use very fine sandpaper to very gently sand the back side of the hole in a circular manner. Place the aluminum in a glassless slide mount. This makes the pinhole a bit more resistant to damage, as well as giving you a place to put notes, like the size of the hole. Voila — a pinhole.
Determining the size of the pinhole is no problem. Raise the negative carrier of your enlarger and focus to the point where 1″ in the carrier will be displayed as 10″ on the board (note: your 35mm carrier may not be 1″ wide, so carefully measure before determining that you have set the proper height). Place the slide in the negative carrier and turn on the enlarger lamp. The projected light will display the hole ten times larger. Place a ruler with a metric scale underneath and examine with a magnifying glass to determine the size of the hole.
I would suggest creating several pinholes and writing their sizes on the slide mount. You can then construct your camera to the focal length of the pinhole. Of course, if the hole is smaller than you would like, you can repeat the series to create a larger pinhole.
Projecting the hole also allows you to closely examine the quality of the hole. Anything other than a clean circular hole will cause additional diffraction.
When you are satisfied with the hole, place a very small piece of tape over the hole while you spray paint it flat matte black. The box you use should also have been spray painted flat matte black.
Determining exposure is only tricky because we are accustomed to using apertures like f8 and f22. In the above example, the f-stop would be 10″ / 0.02345″ or f426. Certainly, you will need to understand the reciprocity of the film you will be using when determining the exposure time. As this could well be into the minutes, as opposed to small portions of a second, an accurate shutter will not be necessary.
So there is your stone knife, to use or abuse it as you wish. tomorrow I will suggest the bear skin, the Van Dyke process, for printing the negatives.
This is the last of five pinhole images offered this week of the result of waves on Tobay Beach, Long Island during the time of Hurricane Bill. The story of these images can be found in those four previous entries. I’ve not shot too many pinhole images of waves coming onto a beach, and this provided me with an opportunity to capture something interesting.
In case anyone is interested, these images were made through my Zero Image 6x9cm. pinhole camera (serial #2) with Acros 100 film, and printed on Oriental Seagul Portrait Warmtone paper toned with selenium.
This is the fourth of five pinhole images offered this week of the result of waves on Tobay Beach, Long Island during the time of Hurricane Bill. Please reference those entries for the earlier section of the story.
I returned to the Atlantic side of the beach, but a ways up from where we had initially looked. This side of the beach was closed for obvious reasons, but since there was a pavilion at that location, I decided to use it to steady my camera. The police were there but I walked past them as if I was supposed to be there. When I arrived at the pavilion there were a number of people congregating in the area, which I came to realize were all the the lifeguards that normally would have been working that area. I set my camera on one of the ledges and started taking pictures. One of the lifeguards came up to me and told me that I really shouldn’t be there. I smiled and nodded, as if to agree with him. Apparently satisfied that he had done his part, he walked away, and I was met by several other lifeguards who asked me about my camera. I did my best to explain the camera and the results I thought I would get. If anyone knows a lifeguard who works at Tobay Beach, perhaps they can be pointed to this entry.
Tomorrow I will show the last image of the series.
This is the third of five pinhole images offered this week of the result of waves on Tobay Beach, Long Island during the time of Hurricane Bill. Please reference those entries for the beginning of the story.
As mentioned yesterday, the others had their own concerns. Although they were close to an entrance to the beach, the incoming wave took them by surprise. One woman (not from our party) was knocked down by the incoming water, while the others fled up the entrance way. As the wave receded she was helped up and had lost a shoe. A shoe laid on the sand and one from our party got the shoe and gave it to her – it wasn’t her shoe.
I finally made it back to the others and we went to the bay side of the Beach. I decided that I wanted to take more pictures, and will continue the story tomorrow.
Yesterday I offered the first of the five pinhole images that are being offered this week and began my explanation, so you may wish to reference that.
Arriving at Tobay Beach, we pulled the car off to the side of the road and walked toward an entrance point to the Atlantic side of the the beach – across the road was the bay side. The others wandered onto the edge of the beach while I continued on to the lifeguard stand, which was also at the edge of the beach but was further from the entrance point. I had only taken a few images when I saw one of the larger waves on its way in. As it crashed onto the beach I realized that although most of the waves had stopped about 50 feet away from me, this one was going to be much different. I jumped onto the lifeguard stand several seconds before about two feet of water crashed below me. The others had their own concerns, which I will mention tomorrow. I completed shooting until I finished the roll of 120 film I had in my pinhole camera.
As Hurricane Bill wandered up the east coast this past summer, I happened to be at Tobay Beach on Long Island, New York. I posted a composite shot of waves coming in at http://glsmyth.wordpress.com/2009/08/23/tobay-beach/, which appear tame unless one looks into the distance and sees a rather large wave on its way.
My primary objective, however, was to take pinhole images of the event. The images I took were in stark contrast some others that showed 5-7 foot waves on their way toward shore. Since all of there images were in the 6-12 second exposure range, the idea was not to capture the waves, but more their effects.
I ended up with five pinhole images that I liked, and this week I will release one each day, as these really should be seen as a set.
Trees will always be a fascination of mine. They are strong, vulnerable, and varied in so many ways. This particular image is a 4X5″ pinhole image taken along a stream that had worked away at the soil around this tree. The roots stand out like a skeleton, offering us a view inside this wonderful tree.
Another image from my Stone Knives And Bear Skins project. I decided to slightly split tone this particular image with a very dilute selenium solution. I pulled it as soon as the color began to change, as leaving it any longer in the toner would have started to bleach the image.
